20 Rowe Drive Jacks Point 9371
Queenstown Lakes · property 181480 · LOT 2050 DP 613113 - 0.112700 Ha CT- 1221386
Every consent eDocs lists on this property
| Consent | Description | Applicant | Status | Status date |
|---|---|---|---|---|
| BC261535 Building | Construction Of Two Storey Multiunit Dwelling With Attached Garage | Application Documentation Checked | ||
| DB251446 | Construction Of A New Two Storey Residential Dwelling With Attached 2 Bedroom Unit | Development Contribution Notice Sent | ||
| BC251446 Building | Construction Of A New Two Storey Residential Dwelling With Attached 2 Bedroom Unit | Building Consent Issued | 4 Feb 2026 |
Consent numbers link to the consent's documents in QLDC eDocs, which needs an eDocs sign-in.
From the documents of BC261535 read 18 Nov 2026
- Value of work
- $900k estimated on the application form, GST included
- Designer
- Simon Garth
simon@peakarchitecture.co.nz
02108873480 - Lodged by
- Not named on the application form
- Timber cladding
-
- WT04 SELECTED SHIPLAP VERTICAL WEATHERBOARDS OVER 20mm
- WT04 SELECTED SHIPLAP VERTICAL WEATHERBOARDS OVER 20mm CAVITY
- JSC TMT TAXON SHIPLAP VERTICAL TIMBER WEATHERBOARDS ON
- WEATHERBOARDS WITH BRUSHED STAIN
- TAXON WEATHERBOARDS WITH WOODX DAMPER
- VERTICAL JSC TIMBER TMT TAXON WEATHERBOARDS WITH BRUSHED STAIN
- JSC TMT TAXON SHIPLAP VERTICAL TIMBER
- WEATHERBOARDS ON HORIZONTAL 20mm H3.1
- JSC TMT TAXON SHIPLAP VERTICAL TIMBER WEATHERBOARDS ON HORIZONTAL 20mm H3.1 CAVITY
- WEATHERBOARD TO STONE CLADDING 3
- JSC TMT TAXON SHIPLAP VERTICAL TIMBER WEATHERBOARDS ON HORIZONTAL 20mm
- WEATHERBOARDS BEYOND THE POINT WHERE BRANZ BULLETIN 411 COMPLIANT WEATHERBOARD LAP OR REBATE COMBINATIONS TERMINATE AT THE CORNER JUNCTION.
- JSC TMT TAXON SHIPLAP VERTICAL TIMBER WEATHERBOARDS ON HORIZONTAL 20mm H3.1
- SHIPLAP WINDOW HEAD DETAIL 1
- SHIPLAP WINDOW SILL DETAIL 2
- SHIPLAP WINDOW JAMB DETAIL 3
- SHIPLAP SLIDING DOOR HEAD/SILL DETAIL 1
- SHIPLAP SLIDING DOOR JAMB DETAIL 2
- Cavity battens: Radiata pine, Treated H3.1 behind weatherboards Cavity battens: 20mm cavity system (Refer details)
- Brand/Type: JSC-TMT® Vertical shiplap weatherboards Fixings: 20mm H3.1 cavity batten, Concealed fixings
- JSC-TMT® Vertical shiplap weatherboards JSC-TMT® Board and Batten weatherboards
- NZS 3617 Profiles of weatherboards, fascia boards and flooring NZS 3631 New Zealand timber grading rules
- BRANZ BU 411 Recommended Timber Cladding Profiles CodeMark™
- JSC VertiClad Vertical Shiplap Weatherboard Cladding Installation Guide v3.7 JSC VertiClad Vertical Shiplap Weatherboard Cladding Design Guide v1.1
- JSC VertiClad Vertical Shiplap Weatherboard System Technical Drawings JSC Verticlad System Installation Checklist
- JSC Board & Batten Weatherboard Cladding Installation Guide v3.7 JSC Board & Batten Weatherboard Cladding Design Guide v1.0
- JSC Board & Batten Weatherboard System Technical Drawings JSC Board & Batten System Installation Checklist
- JSC Exterior Weatherboard Maintenance Guide JSC Structural Cavity Batten Setout and Fixing Guide
- JSC 20mm Cavity Setout For Vertical Weatherboards JSC Coatings Exterior Wood Oil Range
- Weatherboard Cladding Installation guides. Ensure the relevant JSC Weatherboard Cladding System Installation Checklist has been signed off
- this site and building height; as required by NZS 3604. Refer to JSC Weatherboard Cladding Installation guides.
- 2.2 VERTICAL SHIPLAP WEATHERBOARDS Selected timber weatherboards machined to JSC-TMT® profiles, lap and rebate details to BRANZ
- To JSC-TMT® profiles as detailed. Refer to SELECTIONS and JSC Weatherboard Cladding System Technical Drawings.
- Weatherboard Cladding Installation Guides for fixing details. NOTE: Select appropriate nail size / length to achieve the minimum required embedment into the
- Used to retain hidden lap tongues of rebated weatherboard profiles such as vertical shiplap. Refer to JSC Weatherboard Cladding Installation Guides for fixing details.
- 2.11 JSC-TMT® WEATHERBOARD SYSTEM COATING REQUIREMENTS All JSC weatherboards including mouldings must be coated on all sides before installation and
- cavities and 9.4 Timber weatherboards. 3.6 SUBSTRATE
- Foundation and sub-floor framing and NZBC E2/AS1, 9.4 Timber weatherboards. Application - preparation/general
- of weatherboard profiles within a controlled environment delivering a full envelope seal and a premium finish. Additional coatings may need to be applied on site as per the coating
- All JSC uncoated thermally modified timber weatherboards must be coated with one coat of suitable stain to JSC specification on all four sides prior to installation.
- openings (windows, meters, etc.) to JSC Weatherboards Cladding Installation Guides. 20 Rowe Drive, Jacks Point Peak Architecture Lot 2050 363558
- door frames and other penetrations through the cladding to JSC Weatherboards Cladding Installation Guides.
- from the wall underlay towards the back of weatherboards ensuring water is shed away from the framing. Install to JSC 20mm Cavity Setout For Vertical Weatherboards instructions.
- Application - weatherboards 3.12 SET-OUT
- Install to NZBC E2/AS1, 9.4 Timber weatherboards. Coat all cut edges before fixing with JSC specified oil/stain product. Pre-drill all fixings 1mm smaller than nail gauge to ensure a snug fit and
- Refer to JSC Weatherboards Cladding Installation Guides for fixing sizes and details. 3.14 FIXING JSC® VERTICAL SHIPLAP WEATHERBOARDS
- Install to JSC® VertiClad Vertical Shiplap Weatherboards Cladding Installation Guide. Using laser or mechanical devices, set out all nailing accurately in straight lines. Align weather
- JSC TMT® Vertical Shiplap Weatherboards must be pre-drilled with a slight (0-2°) upward slope, 1mm smaller than the nail shank to reduce moisture entry. Single-fix each weatherboard at 35mm
- from the overlapping edge of the weatherboard. Refer to installation guide for minimum embedment of nails into the framing.
- Note: Where vertical weatherboards have an exposed bottom edge such as at the bottom plate, window head, inter storey junction, overhead soffit junction, etc., the bottom edge of the
- weatherboards to be cut with a 15° degree slope to form a drip edge. From the bottom edge, the back of the weatherboards to be coated up to 75-150mm prior to installation.
- All corners to be weatherproofed using corrosion resistant back flashing behind the weatherboards at all external corners to JSC VertiClad Vertical Shiplap Weatherboard Cladding Installation Guide.
- Fix windows to JSC Weatherboards Cladding Installation Guides. 3.16 FLASHING
- Fix to JSC Weatherboard Cladding Installation Guide. Material compatibility to NZBC E2/AS1, Table C.1.1.1B: Compatibility of materials in contact, and Table C.1.1.1C: Compatibility of materials
- Scribers are to be wet-sealed in place and fixed in accordance with JSC Weatherboard Cladding Installation Guide.
- Materials - specific timber weatherboards 4.1 JSC-TMT® TAXON - VERTICAL SHIPLAP WEATHERBOARDS
Plans (PDF, 5.6MB)Project Specification (PDF, 1.5MB)
Lines of the assessment, plans or specification that mention timber cladding. Some describe what the neighbourhood rules allow rather than what is proposed.
From the documents of BC251446 read 19 Nov 2026
- Value of work
- $955k estimated on the application form, GST included
- Designer
- Samantha Hunter
samanthahunterdesign@gmail.com
0273168005 - Engineer
- Hamish Mackinven
hamish@structuraldesignlab.co.nz
0272604088 - Builder
- David Reid Homes Queenstown
jamie.harper@daviddreidhomes.co.nz
027 227 8173 - Licensed: Design
- Samantha Hunter
- Lodged by
- Samantha Hunter Design (Designer engaged by owner to design this home)
samanthahunterdesign@gmail.com
0273168005 - Applicant
- Owner
tarrynreardon@gmail.com
021 242 2661
As written on the application form. Don't add applicants to email marketing lists: that needs their consent. - Timber cladding
- Not mentioned in the documents read